TWO STROKE FOUR STROKE CYCLE ENGINE


×
Rating : Rate It:
 
 
KING    on Apr 12, 2011 Says :

THANX
augusto    on Feb 22, 2011 Says :

very exhaustive and impressive
Post a comment
    Post Comment on Twitter
Comments:  
6 Favorites
sonipalak1990,   favourited this   1 Years ago.
eng_caesar25,   favourited this   2 Years ago.
pavan0311,   favourited this   2 Years ago.
royalslover832,   favourited this   2 Years ago.
ankitmanitripathi1001,   favourited this   4 Years ago.
coolbuddy420,   favourited this   4 Years ago.
First Prev [1] Next Last



  Notes
 
 
1 : 2 Stroke cycle engines http://www.youtube.com/watch?v=LuCUmQ9FxMU
2 : 2 Stroke Engine It's called a two-stoke engine because there is a compression stroke and then a combustion stroke. In a four-stroke engine, there are separate intake, compression, combustion and exhaust strokes.
3 : 2 Stroke cycle engine  Mix special two-stroke oil in with the gasoline Mix oil in with the gas to lubricate the crankshaft, connecting rod and cylinder walls Note:  If you forget to mix in the oil, the engine isn't going to last very long!
4 : Advantage Two-stroke engines do not have valves, which simplifies their construction and lowers their weight. Two-stroke engines fire once every revolution, while four-stroke engines fire once every other revolution. This gives two-stroke engines a significant power boost. Two-stroke engines can work in any orientation, which can be important in something like a chainsaw. A standard four-stroke engine may have problems with oil flow unless it is upright, and 
5 : Advantages These advantages make two-stroke engines lighter, simpler and less expensive to manufacture.  Two-stroke engines also have the potential to pack about twice the power into the same space because there are twice as many power strokes per revolution
6 :
7 : Disadvantages Two-stroke engines don't last nearly as long as four-stroke engines. The lack of a dedicated lubrication system means that the parts of a two-stroke engine wear a lot faster. Two-stroke oil is expensive, and you need about 4 ounces of it per gallon of gas. You would burn about a 3.7 litres of oil every 1600km if you used a two-stroke engine in a car.
8 : Disadvantages Two-stroke engines are not fuel efficient, so you would get fewer miles per gallon. Two-stroke engines produce a lot of pollution 1) from the combustion of the oil. 2) Each time a new charge of air/fuel is loaded into the combustion chamber, part of it leaks out through the exhaust port.
9 : Exhaust  Fuel and air in the cylinder have been compressed, and when the spark plug fires the mixture ignites. The resulting explosion drives the piston downward. Note that as the piston moves downward, it is compressing the air/fuel mixture in the crankcase. As the piston approaches the bottom of its stroke, the exhaust port is uncovered. The pressure in the cylinder drives most of the exhaust gases out of cylinder, as shown here:
10 : Exhaust
11 : Intake As the piston finally bottoms out, the intake port is uncovered. The piston's movement has pressurized the mixture in the crankcase, so it rushes into the cylinder, displacing the remaining exhaust gases and filling the cylinder with a fresh charge of fuel, as shown here:
12 : Intake Note that in many two-stroke engines that use a cross-flow design, the piston is shaped so that the incoming fuel mixture doesn't simply flow right over the top of the piston and out the exhaust port.
13 : Intake
14 : Compression Stroke Now the momentum in the crankshaft starts driving the piston back toward the spark plug for the compression stroke. As the air/fuel mixture in the piston is compressed, a vacuum is created in the crankcase. This vacuum opens the reed valve and sucks air/fuel/oil in from the carburetor. Reed valves are a type of check valve which restrict the flow of fluids to a single direction, opening and closing under changing pressure on each face
15 : Piston functions On one side of the piston is the combustion chamber, where the piston is compressing the air/fuel mixture and capturing the energy released by the ignition of the fuel. On the other side of the piston is the crankcase, where the piston is creating a vacuum to suck in air/fuel from the carburetor through the reed valve and then pressurizing the crankcase so that air/fuel is forced into the combustion chamber. Meanwhile, the sides of the piston are acting like valves, covering and uncovering the intake and exhaust ports drilled into the side of the cylinder wall.
16 :

 

Add as Friend By :
Added On : 6 Years ago.
No piston strokes required for suction/exhaust operations. 2 piston strokes required to complete cy    more
Views 19466 | Favourite 7 | Total Upload :628022

Embed Code:

Flag as inappropriate


Related  Most Viewed



Free Powerpoint Templates



 



Medical PowerPoint Templates | Powerpoint Templates | Tags | Contact | About Us | Privacy | FAQ | Blog

© Slideworld